ncv3

Hey guys, In regards to the pulleys that need to be replaced so I don’t get some type of catastrophic breakdown randomly…….. I know it’s the 2 idlers and the tensioner but also, isn’t there an alternator pulley that can seize? Or is that unlikely? And does it come separate from the alternator...

3 Seat Cloth Bench. OEM Crew. Good condition. I had bought another bench to convert but cannot make the time for yet another project. I need the space and have to sell it. $250 or best offer

Howdy, this is my first post so my apologies if I've messed up, but I have a problem with my windscreen washer pump supply voltage. I've seen similar(ish) posts on the older model, but nothing for the NCV3. Mine is a late 2013 Mercedes Sprinter 316CDi (hence model 906). Essentially the pump...

Hi Guys and Girls, firstly thanks for threads I have been reading, they have started me on my journey of learning about my 2011 NCV3. I just recently picked up a xlwb extra high roof 2wd for living, touring purposes. Im taking an unusual route of upgrading the 316 into the 4’s by way of a rear...

Hey guys, my 07 dodge sprinter 3.0 diesel has 230k miles on it. No major repairs have been done on it, I just do my regular maintenance A and B only. I'm curious on what kind of repairs I should be saving up for in the near future? In specific have you guys fixed EGR valve, oil cooler leaks...

Was on the way to visit relatives in Phoenix before a short hiking stop and got some bad diesel. Van wouldn't accelerate and immedaitely was surging in gas station lot. Was obviously alarmed and pulled over in the lot and turned off the engine. A few minutes later I restarted it and things were...

Hi All, I'm mainly creating this thread to document and gain assistance for retrofitting the D5WS Hydronic Diesel heater to NCV3 Sprinters. I'm fitting one as an engine heater because we plan on going skiing in the Alps and venturing into the Arctic Circle in Finland/Norway. Things to note or...

Hello! I have a bit of a complex issue, at least to my ability and knowledge. I’m travelling in South America with a Sprinter 315 from 2017. I have a faulty ABS sensor on the rear left wheel that caused my ABS, ESP and so on lights to turn on. This sprinter model does not exist in South America...

I am rocking a 2018 (new to me) 144" wb standard roof v6 turbo diesel sprinter. I live in the Colorado Rockies and plan on traveling up to BC/Alaska one day. With the limited availability of 4x4s in the US right now and their $15-20k increased price tag, I opted for an RWD. I am concerned about...

My 2015 Sprinter (2.1L) threw a check engine light yesterday. I checked the codes and got P2201, P22FA, and P22F9 (NOX Sensor 1 bank 1). After reading this thread, I figured I should check the exhaust brackets, and crawled under there. The brackets looked good. But I found something else...

Hi folks, I have an AKE-5 keypad entry module (same manufacturer as provided on many Ford vehicles) but am looking for guidance here on which wires to tap in the door to install the keypad module. I see on other threads that those with them have used audio installers or SMB West for this but I'd...

2013 316CDI MWB. plate says P&W conversion. Has an airmaster AC and doesn't seem to have any condensors in the front engine, so I'm assuming I can't take out the top aircon unit. The interior cargo area aircon components have the wires cut and don't work. There is a fan of sorts near the middle...

Had an expensive "see Dada F's up, too" learning moment for kiddo today. At the very least, I need a new cover & the styrofoam that goes with it.

So my sprinter with 3.0l diesel is at 59700 miles and I'm looking to diy my B service to save money Im not new to diy wrenching (20+ years) or new to german vehicles in general (10+ years) though i am new to mercedes-benz, and sprinters have Mann brand fuel/air/oil filters and liquid moly oil...

hi all, just bought a 2013 316 MWB ex-ambo that I'm going to use for deliveries. It's been stripped a bit too well, & I want to make the back neat again. if anyone has floor, side or rear door panels or cargo barrier they've striped out for a camper conversion, please get in touch! thanks

I am looking for a chopped down bench seat for 2 persons. I am in NJ but willing to drive to pick it up on the east coast. I have a 2016 NCV3

I have a 2008 Dodge Sprinter 3500 and need some advice. It's a fresh purchase and it had the exhaust stolen from it before I bought it. I am looking for a replacement but having trouble to find one in Canada. I am trying to figure out exactly which models I am able to pull a used assembly from...

prefer to sell altogether will not separate at this time. Parts listed are all driver and passenger side front. * factory low seat base in black from vs30 * factory swivels top half from ncv3 bolted onto bottom half from vs30 * factory heated seats with roadtrek leather covers with airbags ***...

The glass on my front passenger is broken and I need to replace the lamp assembly. Can anyone share some info on this? Never done it before and I haven't had much luck searching for a step-by-step guide for the NCV3's. Any reference/info would be greatly appreciated!

This van has been a wonderful passion project and an awesome weekender over the last couple of years, but we are soon moving to SF and will not have the space to keep it. The build is adventure-ready, but I’d say it’s ~95% complete. Most of the work has been completed by me, with the...